Alcatel OS6400-24 Podręcznik Użytkownika Strona 82
- Strona / 152
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Booting Stacked Configurations Booting OmniSwitch 6400 Series Switches
page 4-2 OmniSwitch 6400 Series Hardware Users Guide July 2010
Booting Stacked Configurations
Once the switches have been connected to a virtual chassis, the next step is to manually power on the
stack. The OmniSwitch 6400 Series switch does not use an on/off switch. The power cord is the switch’s
only connect/disconnect device. The power connector socket is located on the switch’s rear panel. For
more information, refer to “OmniSwitch 6400 Series Chassis and Hardware Components” on page 2-1.
To boot the stack, plug the power cord (provided) into the power connector socket at the rear panel of each
switch in the stack. Next, plug all power cords, in rapid succession, into easily-accessible power sources,
such as grounded AC outlets or an Uninterruptible Power Supply (UPS).
Note. Be sure to power on all switches in the stack in rapid succession; otherwise, switches may be
assigned unintended stack management roles. Refer to Chapter 6, “Managing OmniSwitch 6400 Series
Stacks.” for detailed information.
The stack immediately begins the boot process. Allow a few moments for all elements in the stack to boot
completely, then verify the status of all LEDs on the switch’s front panel. A successful boot for a stacked
OmniSwitch displays the following LED states.
If any of the LED state differs from the states shown in the table above, refer to page 2-20 for more infor-
mation. Contact Alcatel-Lucent Customer Support if the LED state persists.
LED States for a Stacked Configuration
OK Solid green for all switches.
PRI Solid green: Primary management module
Solid amber: Secondary management module
Off: Idle (Neither primary or secondary)
Detailed information for primary, secondary, and idle roles is provided
in Chapter 6, “Managing OmniSwitch 6400 Series Stacks.”
PWR Solid green for all switches.
BPS Solid green: Operational
Solid amber: Failed
Off: Not present
Slot Indicator 1–8: Depending on the slot number assignment for each switch. See
Chapter 6, “Managing OmniSwitch 6400 Series Stacks.” for detailed
information.
- OmniSwitch 6400 Series 1
- Hardware Users Guide 1
- Contents 3
- About This Guide 9
- Unsupported Platforms 10
- Who Should Read this Manual? 11
- What is in this Manual? 11
- What is Not in this Manual? 11
- Documentation Roadmap 12
- Related Documentation 14
- Technical Support 15
- 1 OmniSwitch 6400 Series 17
- Availability Features 19
- Hot Swapping 20
- Hardware Monitoring 20
- 2 OmniSwitch 6400 Series 21
- Chassis and Hardware 21
- Components 21
- OmniSwitch 6400-24 Rear Panel 23
- OS6400-24 Specifications 24
- OS6400-P24 Specifications 27
- OS6400-U24 Specifications 30
- OS6400-U24D Specifications 33
- OmniSwitch 6400-48 34
- OmniSwitch 6400-48 Rear Panel 35
- OS6400-48 Specifications 36
- OS6400-P48 Specifications 39
- LED Status Indicators 40
- PS-510W-AC Power Supply 42
- PS-510W-AC-E Power Supply 43
- PS-360W-AC Power Supply 44
- PS-360W-AC-E Power Supply 45
- PS-126W-AC Power Supply 46
- PS-120W-DC Power Supply 47
- 126W AC Internal Power Supply 48
- 120W DC Internal Power Supply 48
- Power Supply Shelf 49
- AC Power Cords 50
- DC Power Specifications 51
- Console Port 52
- Port Pinouts 54
- 3 Mounting OS6400 57
- Switches 57
- Reduced Air Flow 58
- Mechanical Loading 58
- Circuit Overloading 58
- Reliable Earthing 58
- Airflow Recommendations 59
- Fan Speed Control 60
- Installation Overview 61
- Tabletop Installation 62
- Next Steps 63
- Rack-Mount Installation 64
- Recommended Cabling Patterns 66
- Cabling Steps 67
- Installing Power Supplies 69
- Rack Mounting Power Supplies 71
- Redundant 510W-PoE 73
- AC Power Supply Connections 75
- DC Power Supply Connections 76
- DC Power Source 78
- OS6400 Power Supply 78
- Hot-Swapping Power Supplies 79
- 4 Booting OmniSwitch 6400 81
- Series Switches 81
- Monitoring the Chassis 83
- Checking the Fan Status 84
- 5 Managing Power over 85
- Ethernet (PoE) 85
- Power over Ethernet Defaults 89
- Disabling PoE 90
- Setting Port Priority Levels 91
- Disabling Priority Disconnect 93
- Enabling Priority Disconnect 93
- 6 Managing OmniSwitch 99
- 6400 Series Stacks 99
- In This Chapter 100
- Roles Within the Stack 101
- Using the Chassis MAC Address 104
- Using Saved Slot Information 105
- Using Switch Uptime 106
- Idle Module Role 109
- Pass-Through Mode 110
- Stack Redundancy and Failover 114
- Slot Numbering 116
- Manual Slot Number Assignment 119
- Merging Stacks 122
- Reloading Switches 123
- -> reload primary 124
- -> reload secondary 125
- -> reload ni 3 127
- -> reload all 128
- Avoiding Split Stacks 130
- -> takeover 131
- Monitoring the Stack 134
- Management Modules 135
- A Regulatory Compliance 137
- 产品说明书附件 138
- Statement 140
- Standards Compliance 141
- FCC Class A, Part 15 142
- Canada Class A Statement 142
- CISPR22 Class A warning 142
- Translated Safety Warnings 144
- Installation Warning 145
- Lithium Battery Warning 146
- Operating Voltage Warning 146
- Power Disconnection Warning 147
- Wrist Strap Warning 149
- Clase de seguridad 151
Powiązane produkty i podręczniki dla Networking Alcatel OS6400-24
Networking Alcatel OS6850-48 Dokumentacja
(35 strony)
(35 strony)
Networking Alcatel OS6850-48 Podręcznik Użytkownika
(192 strony)
(192 strony)
Networking Alcatel OS6602-24 Podręcznik Użytkownika
(120 strony)
(120 strony)
Networking Alcatel 1000 ADSL Dokumentacja
(20 strony)
(20 strony)
Networking Alcatel OS6602-48 Podręcznik Użytkownika
(628 strony)
(628 strony)
© 2020, manymanuals.pl. Wszelkie prawa zastrzeżone. | 0.063 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentarze do niniejszej Instrukcji